uProcess™ Automated Pumps, Valves and Sensors
The LabSmith breadboard-based uProcess™ automated syringe pumps, valves, pressure and temperature sensors are part of the uProcess microfluidics automation system of software and hardware products which provides simple, straightforward automated routing of microfluidic volumes.
uProcess automated devices work together with CapTite™ microfluidic interconnect products to make it easy to build and rebuild micro- and nano-fluidic circuits. All products are inter-compatible and quick to assemble, taking the hassle out of fluid routing and control.
All uProcess devices are connected through a common bus on the uPB Breadboard to an interface box, communicating with the software through a USB interface. One control interface can sequence and coordinate more than 30 devices, and breadboards can hold 5, 8 or 12 devices each.
- Automated 3 port Valve
To €672.59AV201 Automated Valves.
Two-position three-port automated valves. Available for 360um capillary, 1/32" tubing or 1/16" tubing. Requires a 4VM valve manifold and EIB controller for communicating with PC. Connects to capillary or tubing via one-piece fitting (not included). Learn More
- uPS Pressure Sensor
- USB uProcess Electronic Interface Controller€161.83 As low as €121.37EIB-200 USB Electronic Interface Controller.
Controls over 100 uDevices for sequential operation and up to 10 uDevices for simultaneous operation. Includes uProcess software, power supply, micro USB 2.0 cable, and flat ribbon connection cable. Compatible with uProcess Software versions 1.24.4 and later. Learn More
- Automated 4 port Valve
To €773.72AV202 Automated Valve
Two-position four-port automated valve with "II" shaped flow pattern. Available for 360um or 1/32" tubing size. Requires a 4VM valve manifold and EIB controller for communicating with PC. Connects to capillaries/tubing via one-piece fittings (not included).
- uProcess Power Manifold€252.85 As low as €189.644PM01 uProcess Power Manifold.
Power manifold for automatable and closed-loop control of up to 4 uTE thermal-electric modules or other loads using the LabSmith uProcess software.
Includes 4 flat flex ribbon cables (1 x 8", 2 x 10", 1 x 12").
- Voltage range: –5 to 5 V
- Current range: -4 to 4 A
- Maximum Power: 15 W
- Dimensions: 2.1" x 1.0" x 0.5" (54 mm x 26 mm x 13 mm)
- uTE Thermal-Electric Module€151.71LabSmith uTE-series thermal-electric module.
The uTE module is used for heating or cooling your microfluidic application. The module can be coupled with a uTS temperature sensor for precision thermal monitoring and control using LabSmith's uProcess software.
The uTE-series thermal-electric modules require a 4PM01 Power Manifold and EIB200 uprocess interface. A uTS temperature sensor is recommended for monitoring and control of the uTE module.
- uTS Temperature sensors
To €121.37LabSmith uTS-series temperature sensors.
The uTS can be used alone for on-chip or in-fluid temperature monitoring, or with the uTE-series thermal-electric module for complete temperature control. Controlled using the LabSmith uProcess software suite or LabView, the uTS and uTE precision thermal management products are a perfect compliment to LabSmith's complete monitoring and control of microfluidic systems.
The uTS-series temperature sensors require a 4AM01 sensor manifold and EIB200 USB interface.
- Temperature range: -150 – 200° C
- Sensor type: K-type thermocouple
- Accuracy: 0.5° C
- Precision: 0.001° C
- AV801 Automated 8-Port Selector Valve€1,006.35AV-801-T116K
8 position selector valve for 1/16" OD capillary. Allows connection of any of the 8 port to the central port for fluidic distribution or selection. Nine (9) T-116-100 fittings required for interface to capillary (not included). Wetted material: VespelAV801-C360V
8 position selector valve for 360 um OD capillary. Allows connection of any of the 8 port to the central port for fluidic distribution or selection. Nine (9) C360-100 fittings required for interface to capillary (not included). Wetted material: VespelAV801-T132V
8 position selector valve for 1/32" tubing OD capillary. Allows connection of any of the 8 port to the central port for fluidic distribution or selection. Nine (9)T132-100 fittings required for interface to capillary (not included). Wetted material: Vespel
Selected valves are available with PCTFE Kel-F® as the wetted material.Learn More